manualshive.com logo in svg

HIKVISION DS-7200-SH, User Manual, Page: 106 / 188

Share
Download
HIKVISION DS-7200-SH User Manual Download Page 106

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR 

10
4 

 

 

 

 
 

7.1.4 Backing up Video Clips

 

 

 

Purpose:

 

 

You  may  also  select  video  clips  to  export  directly  during  Playback,  using  USB  devices  (USB  flash  drives, 

USB HDDs, USB writer), SATA writer or eSATA HDD. 

Note: 

The eSATA writer is supported by DS-7300-SH and DS-8100-SH models only. 

 

Steps:

 

 

1.  

Enter Playback interface. 

 

Please refer to 

Chapter 6

. 

2.  

During playback, use buttons  

  and  

  in the playback toolbar to start or stop clipping record file(s). 

3.  

Exit Playback interface after finishing clipping and you will then be prompted to save the clips. 

 

Note: 

A maximum of 30 clips can be selected for each channel. 

 

Figure 7.18 Interface of Playback by Time 

 

 

4.  

Click 

Yes 

to save video clips and enter Export interface, or click 

No 

to quit and do not save video clips. 

 

Figure 7.19 Attention to Video Clip Saving 

 

 

5.  

Export the video clips. 

 

Click 

Export 

button and start backing up. 

 

Note: 

If the inserted USB device is not recognized: 

• 

Click the 

Refresh 

button. 

• 

Reconnect device. 

• 

Check for compatibility from vendor. 

You can also format USB flash drive or USB HDDs via the device. 

Summary of Contents for DS-7200-SH





























































































































































































Reviews:

No comments