HIKVISION DS-7200-SH User Manual Download

Page: 154 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

152

10.4 Configuring Quota Mode

Purpose

Each camera can be configured with allocated quota for the storage of recorded files.

Steps

Enter the Storage Mode interface.

Menu > HDD > Advanced

Set the

Mode

Quota

Note:

The device must be rebooted to enable the changes to take effect.

Figure 10.14 Storage Mode Settings Interface

Enter the storage capacity in the text field of

Max. Record Capacity (GB)

Figure 10.15 Configure Record Quota

You can copy the quota settings of the current camera to other cameras if required. Click the

Copy

button

to enter the Copy Camera menu, as shown below.

Figure 10. 16 Copy Settings to Other Camera(s)

Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands

HIKVISION DS-7200-SH, User Manual

Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands