HIKVISION DS-7200-SH User Manual Download

Page: 25 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

Figure 1.10 Rear Panel of DS-7316HFI-SH and DS-7316HWI-SH

Note:

The rear panel of DS-7304HFI-SH/DS-7304HWI-SH provides 4 video input interfaces, and the rear

panel of DS-7308HFI-SH/DS-7308HWI-SH provides 8 video input interfaces.

Table 1.9 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

MAIN VIDEO OUT

BNC connector for video output.

SPOT VIDEO OUT

BNC connector for spot video output.

HDMI

HDMI video output.

USB Interface

Connects USB mouse or USB flash memory devices.

RS-232

Connector for RS-232 devices.

VGA

DB15 connector for VGA output. Display local video output and menu.

AUDIO IN

RCA connector for audio input.

AUDIO OUT

RCA connector for audio output.

LAN Interface

RJ45 10M/100M/1000M Ethernet interface.

RS-485 Interface

Connector for RS-485 devices. Connect the D+ and D- terminals to R+ and
R- terminals of PTZ receiver respectively.

Alarm In/Out

Connector for alarm input/output.

eSATA

Connects external SATA HDD, DVD-R/W.

100~240VAC

100~240VAC power supply.

POWER

Switch for turning on/off the device.

GND

Ground (needs to be connected when DVR starts up)

DS-7332HFI-SH, DS-7332HWI-SH and DS-7332HI-SH:

The rear panel of DS-7332HFI-SH, DS-7332HWI-SH and DS-7332HI-SH DVR is shown in Figure 1.11.

Figure 1.11 Rear Panel of DS-7332HFI-SH, DS-7332HWI-SH and DS-7332HI-SH

Note:

DS-7324HFI-SH, DS-7324HWI-SH and DS-7324HI-SH models provide 24 video input interfaces on

the rear panel.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands

HIKVISION DS-7200-SH, User Manual

Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands