HIKVISION DS-7200-SH User Manual Download Page 55

Page: 55 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

5.1 Configuring Encoding Parameters

Purpose:

By configuring the encoding parameters you can define the transmission stream type, the resolution and so on.

Before you start:

Make sure that the HDD has already been installed. If not, please install a HDD and initialize it.

(Menu>HDD>General)

Figure 5.1 HDD- General

Check the storage mode of the HDD

1) Click

Advanced

to check the storage mode of the HDD.

2) If the HDD mode is

Quota

, please set the maximum record capacity. For detailed information, see

Chapter 10.4 Configuring Quota Mode

3) If the HDD mode is

Group

, you should set the HDD group. For detailed information, see

Chapter

5.8 Configuring HDD Group for Record

Figure 5.2 HDD- Advanced

Steps

Enter the Record settings interface to configure the encoding parameters:

Menu>Record>Encoding

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 55 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: