HIKVISION DS-7200-SH User Manual Download Page 129

Page: 129 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

127

Figure 9.7 PPPoE Settings Interface

Check the

PPPoE

checkbox to enable this feature.

Enter

User Name

and

Password

for PPPoE access.

Note:

The User Name and Password should be assigned by your ISP.

Figure 9.8 PPPoE Settings Interface

Click the

Apply

button to save and exit the interface.

After successful settings, the system asks you to reboot the device to enable the new settings, and the

PPPoE dial-up is automatically connected after reboot.

You can go to Menu>Maintenance>System Info>Network interface to view the status of PPPoE

connection. Please refer to

Chapter 12.1Viewing System Information

for PPPoE status.

9.2.2 Configuring DDNS

Purpose:

If your device is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to

be used for network access.

Prior registration with your ISP is required before configuring the system to use DDNS.

Steps:

Enter the Network Settings interface.

Menu > Configuration > Network

Select the

DDNS

tab to enter the DDNS Settings interface.

Figure 9.9 DDNS Settings Interface

Check the

DDNS

checkbox to enable this feature.

Select

DDNS Type

. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull,

NO-IP and hkDDNS.

•

IPServer:

Enter

Server Address

for IPServer.

Note:

The

Server Address

should be the IP address of the PC that runs IPServer.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 129 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: