HIKVISION DS-7200-SH User Manual Download Page 27

Page: 27 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

Table 1.11 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

MAIN VIDEO OUT

BNC connector for video output.

SPOT VIDEO OUT

BNC connector for spot video output.

CVBS AUDIO OUT

RCA connector for audio output. This connector is synchronized with

CVBS video output.

VGA AUDIO OUT

RCA connector for audio output. This connector is synchronized with VGA

video output.

LINE IN

RCA connector for two-way audio input.

AUDIO IN (1-4)

RCA connector for audio input.

AUDIO IN (5-16)

DB26 connector for audio input.

VGA

DB15 connector for VGA output. Display local video output and menu.

RS-232

Connector for RS-232 devices.

HDMI

HDMI video output.

USB Interface

Connects USB mouse or USB flash memory devices.

LAN1/LAN2 Interface

2 RJ45 10M/100M/1000M Ethernet interfaces.

eSATA

Connects external SATA HDD, DVD-R/W.

Termination Switch

RS-485 termination switch. Up position is not terminated.

Down is terminated with 120Ω resistance.

RS-485 Interface

Connector for RS-485 devices. Connect the T+ and T- terminals to the R+

and R- terminals of PTZ receiver respectively.

Connect the D+ and D- terminals to Ta and Tb terminals of the controller.

For cascading devices, the first DVR’s D+ and D- terminals should be

connected with the D+ and D- terminals of the next DVR.

Alarm In/Out

Connector for alarm input/output.

GND

Ground(needs to be connected when DVR starts up)

100~240VAC

100~240VAC power supply.

POWER

Switch for turning on/off the device.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 27 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: