HIKVISION DS-7200-SH User Manual Download Page 135

Page: 135 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

133

9.2.6 Configuring Remote Alarm Host

Purpose:

With a remote alarm host configured, the device will send the alarm event or exception message to the host

when an alarm is triggered. The remote alarm host must have the CMS (Client Management System) software

installed.

Steps:

Enter the Network Settings interface.

Menu > Configuration > Network

Select the

More Settings

tab to enter the More Settings interface.

Figure 9.23 More Settings Interface

Enter

Alarm Host IP

and

Alarm Host Port

in the text fields.

The

Alarm Host IP

refers to the IP address of the remote PC on which the CMS (Client Management

System) software (e.g., iVMS-4200) is installed, and the

Alarm Host Port

must be the same as the

alarm monitoring port configured in the software (default port is 7200).

Figure 9.24 Configure Alarm Host

Click the

Apply

button to save and exit the interface.

9.2.7 Configuring Multicast

Purpose:

The multicast can be configured to realize live view for more than the maximum number of cameras through

network.

A multicast address spans the Class-D IP range of 224.0.0.0 to 239.255.255.255. It is recommended to use the

IP address ranging from 239.252.0.0 to 239.255.255.255.

Steps:

Enter the Network Settings interface.

Menu > Configuration > Network

Select the

More Settings

tab to enter the More Settings interface.

Set

Multicast IP

. When adding a device to the CMS (Client Management System) software, the

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 135 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: