manualshive.com logo in svg

HIKVISION DS-7200-SH, User Manual, Page: 156 / 188

Share
Download
HIKVISION DS-7200-SH User Manual Download Page 156

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR 

154 

 

 

 

 

 
 

10.5 Checking HDD Status

 

 

 

Purpose:

 

 

You may check the status of the installed HDDs on device so as to take immediate check and maintenance in case 

of HDD failure. 

Checking HDD Status in HDD Information Interface

 

 

Steps:

 

 

1. 

Enter the HDD Information interface. 

 

Menu > HDD>General 

 

2. 

Check the status of each HDD which is displayed on the list. 

 

Figure 10.17 View HDD Status (1) 

 

 

Note: 

If the status of HDD is 

Normal 

or 

Sleeping

, it works normally. If the status is 

Uninitialized 

or 

Abnormal

, 

please initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new one. 

Checking HDD Status in HDD Information Interface

 

Steps:

 

 

1. 

Enter the System Information interface. 

 

Menu > Maintenance > System Info 

 

2. 

Click the 

HDD 

tab to view the status of HDD displayed on the list. 

 

 

 

Figure 10.18 View HDD Status (2) 

Summary of Contents for DS-7200-SH





























































































































































































Reviews:

No comments