GSK GSK983Ma, User Manual

Page: 30 / 373

GSK983Ma Milling Machine Center CNC System User Manual
18
Part 1 Programming
Note 4: The numbers can be used with or without the decimal point
X1000 Y23.7
；
X10 Y22359 ；
Note 5: If the value specified is less than the value of the least input increment, and this value is then
omitted. When the X1.23456 is specified, it is treated as X1.234 in metric, and it is regarded as
1.2345 in inch. The accumulation error occurs when the incremental value is specified, the
accumulation error does not issue but its error omitted when the absolute value is specified.
The specified digits can not exceed the maximum allowance digits.
X1.23456789……has an error due to it exceeds 8 digits.
X1.2345678……does not an error because it is within the 8 digits.
Note 6: When a number with a decimal point is input which is converted into an integer of the least
input increment.
(For example) X12.34 12340 (Input in Metric)
The converted integer should be checked, still.
(For example) X1234567.8 X1234567800 (Input in Metric). The alarm may occur due to this
number is more than 8 digits.
3.2.5 The maximum command value
Note that the maximum commanded value range of NC device is expressed in the following table
instead of the mechanical movement range of NC machine. For example, the movement of X axis for
the NC device is about 100m (Input in Metric). As for a certain machine, the stroke distance of X axis
may limit within 2m, as the feedrate. The cutting feedrate of NC device can be set to 30m/min, but the
NC machine side may limit within 6m/min. In the actual programming, refer to this manual and the
manual issued from the manufacturer at the same time. Program can be performed after
comprehending the special machine program fully. The maximum command value of each address is
shown below:
Table 3.5 The basis address and the range of command value (the additional selection
included)
Name Address
Input in mm
Output in mm
Input in inch
Output in mm
Input in mm
Output in inch
Input in inch
Output in inch
Program
number
：（
ISO
）
O
（
EIA
）
1
～
9999 As the left As the left
As the left
Sequence
number
N
1
～
9999
″ ″ ″
Preparation
function
G
0
～
99
″ ″ ″
Coordinate
word
X
、
Y
、
Z
、
I
、
J
、
K
、
Q
、
R
、
A
、
B
、
C
、
U
、
V 、 W
±99999.999mm
±99999.999°
±3937.0078inc
h
±99999.999°
±99999.999mm
±99999.999°
±3937.0078inch
±9999.999°
Feed per
minute
F
1 mm/min
～
30000mm/min
0.01 inch/min
～
1200.00inch/mi
n
1 mm/min
～
30000mm/min
0.01inch/min
～
1200.00inch/min
Feed per
minute
(feedrate
1/10)
(Parameter
setting)
F
0.1 mm/min
～
30000.0mm/min
0.01 inch/min
～
1200.00inch/mi
n
0.1 mm/min
～
30000.0mm/min
0.01inch/min
～
1200.00inch/min
Spindle
function
S 0 ～ 30000 0 ～ 30000 0 ～ 30000 0 ～ 30000
Tool function T 0 ～ 9999 ″ ″ ″
Miscellaneous
function
M 0 ～ 99 ″ ″ ″
Dwell X
0 s
～
99999.999s
″ ″ ″