GSK GSK983Ma, User Manual

Page: 7 / 373

List
VII
List
Programming
Programming.......................................................................................................................................1
Chapter One General........................................................................................................................1
1.1 G
ENERAL
............................................................................................................................................... 1
1.2 C
AUTIONS FOR
R
EADING THIS
M
ANUAL
.................................................................................................. 1
Chapter Two Specification ................................................................................................................3
Chapter Three Programming ..........................................................................................................13
3.1 W
HAT IS
P
ROGRAMMING
........................................................................................................................ 13
3.2 P
ROGRAM
S
TRUCTURE
........................................................................................................................... 13
3.2.1 Block
............................................................................................................................................. 14
3.2.2 Program Word
............................................................................................................................. 14
3.2.3 Input format .................................................................................................................................. 16
3.2.4 Decimal point programming ...................................................................................................... 17
3.2.5 The maximum command value ................................................................................................. 18
3.2.6 Program number
......................................................................................................................... 19
3.2.7 Sequence number
...................................................................................................................... 20
3.2.8 Skip to optional block
................................................................................................................. 20
3.3 D
IMENSION
W
ORD
.................................................................................................................................. 21
3.3.1 Controlled axis ............................................................................................................................. 21
3.3.2 Setting unit ................................................................................................................................... 22
3.3.2.1 The least input increment and the least movement unit .......................................................... 22
3.3.2.2 10 folds input unit.................................................................................................................... 23
3.3.3 The maximum stroke
.................................................................................................................. 24
3.3.4 Program origin and coordinate system .................................................................................... 24
3.3.5 The coordinate system and the machining start point ........................................................... 24
3.3.6 Workpiece coordinate system ................................................................................................... 25
3.3.7 Reference (position) point
......................................................................................................... 26
3.3.8 Absolute and incremental commands
..................................................................................... 26
3.4 F
EED
F
UNCTION
(F
FUNCTION
)............................................................................................................... 27
3.4.1 Rapid traverse rate
..................................................................................................................... 27
3.4.2 Cutting Feedrate ......................................................................................................................... 28
3.4.3 Feedrate decelerates to 1/10 .................................................................................................. 29
3.4.4 Synchronous feed (feed/rev.)
.................................................................................................... 29
3.4.5 F1-digit Feed
............................................................................................................................... 30
3.4.6 Automatic acceleration/deceleration
........................................................................................ 30
3.4.7 Automatic Corner Modification .................................................................................................. 31
3.4.7.1 The automatic modification of inner corner ............................................................................ 31
3.4.7.2 The change of inner side arc cutting........................................................................................ 34
3.5 P
REPARATION
F
UNCTION
(G
FUNCTION
)................................................................................................. 35
3.5.1 Plain Selection (G17, G18, G19)
.............................................................................................. 38
3.5.2 Positioning (G00)
........................................................................................................................ 38
3.5.3 Single Direction Positioning (G60)
........................................................................................... 39
3.5.4 Linear interpolation (G01) ........................................................................................................ 40
3.5.5 Circular Interpolation (G02, G03) ............................................................................................. 42
3.5.5.1 Circular interpolation without an additional axis .................................................................... 42
3.5.5.2 Arc interpolation with additional axis ..................................................................................... 44
3.5.6 Sine curve interpolation
............................................................................................................. 45
3.5.7 Thread Cutting (G33)
.............................................................................................................. 46
3.5.8 Automatic reference position return (Reference position G27
～
G30) ................................ 48
3.5.8.1 Reference position return check (G27).................................................................................... 48
3.5.8.2 Automatically return to the reference position (G28).............................................................. 48
3.5.8.3 Return from the reference position automatically (G29)......................................................... 49
3.5.8.4 2
nd
, 3
rd
and 4
th
reference position return
（
G30
）
................................................................. 51
3.5.9 Dwell (G04) .................................................................................................................................. 51