GRAUPNER mx-16 HOTT, Programming Manual

Page: 59 / 180

59 Program description: base settings - fi xed-wing model
here. The software provides a maximum of twelve
ready-made mixers for up to two aileron servos and two
camber-changing fl ap servos.
Note:
If your model is equipped with only one fl ap servo, you
should still select “2ail2fl ”, but leave the “AIL
¼
FL”
mixer in the “ Wing mixer ” menu, which is described on
page 91, at 0%. In contrast, all the other wing mixers
can be used in the usual way. The second fl ap socket
which is now “vacant” must ON NO ACCOUNT be used
for any other purpose!
timer
Two timers are shown in the basic display: one stop-
watch and one fl ight timer:
GRAUBELE
#01
0:00h
stop
flt 0:00
0:00
0.0V
6.1V HoTT
M
99%
You can assign a physical switch or a control switch to
these two timers in the right-hand column of the “timer”
line, indicated by the switch symbol
at the bottom
edge of the screen.
motor at C1 idle re.
tail type nor mal
cut off +100% –125% 9
aile/flap 2aile
timer 0:00 –––
The assigned switch starts both timers, and also halts
the stopwatch.
The method of assigning a physical switch or a control
switch is described on page 39.
The fl ight timer, and the saving of telemetry data on
a memory card fi tted in the card slot (see page 22),
always starts simultaneously with the stopwatch, but
continues to run even when the stopwatch is halted
(switched off). It can only be stopped by touching the
central
ESC button of the left-hand touch-key when the
stopwatch is already halted.
Once the timers are stopped, you can reset both timers
to their initial value by briefl y pressing the
cd
or
ef
buttons of the right-hand touch key ( CLEAR ).
Switching between “count-up” and “count-down”
Count-up timer (stopwatch function)
If you assign a switch and start the stopwatch with the
initial value of “0:00”, the timer runs up until the maxi-
mum of 180 minutes and 59 seconds, then re-starts at
0:00.
Count-down timer (alarm timer function)
You can select a starting time within the range 0 to 180
minutes in the left-hand minutes fi eld, and a starting
time within the range 0 to 59 seconds in the right-hand
seconds fi eld. Any combination of times can also be
selected.
Simultaneously touching the
cd
or
ef
buttons of the
right-hand touch-key ( CLEAR ) resets any settings you
have made to “0” or “00”.
motor at C1 idle re.
tail type nor mal
cut off +100% –125% 9
aile/flap 2aile
timer 0:00 2
Procedure
Select the desired input fi eld using the arrow buttons 1.
ef
of the left or right-hand touch-key.
Touch 2. SET in the centre of the right-hand touch-key.
Select the required time in the highlighted minutes 3.
and seconds fi elds using the arrow buttons of the
right-hand touch-key.
Touch the central
4. SET button to conclude the input
process.
Once you have switched back to the basic dis-
5.
play by touching the central ESC button of the left-
hand touch-key the required number of times, touch
the
cd
or
ef
buttons of the right-hand touch-
key ( CLEAR ) simultaneously, with the stopwatch
stopped, to switch the stopwatch to the “Timer” func-
tion; see top right in the following illustration:
GRAUBELE
#01
0:00h
stop
flt 10:01
0:00
0.0V
6.1V HoTT
M
99%
When you operate the assigned switch, the stopwatch
now starts from the set initial value,
counting down
(“Timer function”). When the set time has elapsed, the