GRAUPNER mx-16 HOTT, Programming Manual

Page: 25 / 180

25 Description of transmitter - screen and keypad
Operating the “Data Terminal”
Input buttons ESC , SET , CLEAR ,
symbols
On-screen telemetry symbols
The active model memory is not yet “bound”
Not fl ashing: RF switched off at transmitter
Flashing aerial symbol:
The last receiver bound to the active model is
inactive, or out of range
> M x No telemetry signal detected
> M Signal strength display
> P Display of Pupil signal strength on the Teacher
transmitter’s screen.
Buttons to the left of the screen
ESC • button
A brief press on the ESC button returns you step by
step within the function select system, taking you
right back to the basic display. If you make a change
in the meantime, the change is retained.
If touched for about three seconds in the base dis-
play,
ESC opens and closes the Telemetry menu.
Arrow buttons •
ef cd
A brief press on one of these buttons allows you 1.
to leaf through lists, such as the Model Select or
Multi-Function list, always moving in the direction
of the arrow; the arrow buttons are also used to
move through menu lines within menus.
A brief simultaneous press of the
2.
ef
buttons
switches from the base transmitter display, and
from almost any menu position, into the “
Servo
display ” menu.
Buttons to the right of the screen
SET • button
Starting from the base screen display - as it ap- 1.
pears when you switch the transmitter on - a brief
press of the
SET button takes you to the multi-
function menus. You can also call up a selected
menu using the
SET button.
Within the set-up menus you can activate (con- 2.
fi rm) and disable the corresponding set-up fi elds
with a brief press of the
SET button.
Arrow buttons •
ef cd
1. “Leafs through” the multi-function menu and the
menu lines within the set-up menus, in the same
manner as the left-hand touch-key’s arrow but-
tons.
2. Selects and adjusts parameters in set-up fi elds af-
ter you have activated them by briefl y pressing
the
SET button; the buttons
fc
and
ed
are
assigned the same function in each case, i. e. it
makes absolutely no difference which of the two
buttons you use.
3. A brief simultaneous press of the
cd
or
ef
buttons resets an altered parameter value in the
active input fi eld to the default value (
CLEAR ).
Notes:
It is not the contact with the touch-key itself that trig- •
gers the corresponding action, but the cessation of
the touch.
If you switch the transmitter off and then immediate-
•
ly on again, you may fi nd that the touch-keys have
no effect. This is not a fault! Switch the transmitter off
again, and wait a few seconds before switching it on
once more.
Short-Cuts
You can call up particular menus or options directly us-
ing the following button combinations:
CLEAR •
A brief simultaneous press of the
cd
or
ef
but-
tons of the right-hand touch-key resets an altered pa-
rameter value in the active input fi eld to the default
value.
“
• Servo display ”
A brief simultaneous press of the
ef
buttons of the
left-hand touch-key switches from the transmitter’s
base display, and from almost any menu position, to
the “
Servo display ”, menu; see page 113.
“ • Telemetry ”
Press the central ESC button of the left-hand touch-
key for about three seconds at the transmitter’s base
display; see section starting on page 117.
“
• HIDDEN MODE ”
(language selection and contrast)
Simultaneously press the arrow buttons
cd
of the
left-hand touch-key AND the central SET button of
the right-hand touch-key; see next page.
Input lock •
Can be activated and disabled at the transmitter’s ba-
sic display by simultaneously holding the
ESC and
SET buttons pressed in for about two seconds.