GRAUPNER mx-16 HOTT, Programming Manual

Page: 129 / 180

129 Program description: Telemetry menu
The meanings are as follows:
Value Explanation
BAT1 / BAT2 Battery 1 / Battery 2
FUEL Fuel level / Fueltank indicator
E / F Empty / full
T1 / T2 Temperature of sensor 1 / sensor 2
CELL V Cell voltage of cell 1 … max. 6
ALT Current altitude
0m1 m/1 sec climb / descent
0m3 m/3 sec climb / descent
CURRE. Actual current in Ampere
POWER Actual voltage of drive battery
RX + ELECTRIC AIRMODUL
0.0V 0m/3s
BAT1 0m/1s
BAT2
0.0V T2 +20°C
T1 +20°C
CELL V
1L0.00
2L0.00
3L0.00
4L0.00
5L0.00
6L0.00 0.0V 0A
ALT +500m
7L0.00
0.0V 0m/3s
BAT1 0m/1s
BAT2
0.0V T2 +20°C
T1 +20°C
CELL V
1H0.00
2H0.00
3H0.00
4H0.00
5H0.00
6H0.00 0.0V 0A
ALT +500m
7H0.00
If an Electric-Air module, Order No. 33620 , is connected
to the receiver, then this screen provides a graphic
display of the data supplied by it. For more information
on this module please see the Appendix, or refer to the
product on the Internet at www.graupner.de.
Depending on the types of sensor fi tted to the module,
the display constantly shows the following data:
The actual voltage of up to two rechargeable batteries
(BAT1 and BAT2); the measured values from up to two
temperature sensors (T1 and T2); the current altitude
relative to the location, and the climb / descent of the
model in m/1sec and m/3sec; the centre of the screen
also displays the current actually being drawn from a
power source.
At the right-hand edge the screen shows an alternating
display of the actual cell voltages of the battery packs
(max. seven cells each) connected to balancer sockets
1 (L) or 2 (H).
The meanings are as follows:
Value Explanation
V Actual voltage
A Actual current
BAT1 / BAT2 Battery 1 / Battery 2
ALT Current altitude
m/1s m/1 sec climb / descent
m/3s m/3 sec climb / descent
T1 / T2 Temperature from sensor 1 / 2
CELL.V Cell voltage of cell 1 … max. 14
L Balancer socket 1
H Balancer socket 2
RX + VARIO
RXSQ
0
MAX
+500m
MIN
+500m
ALT
+500
H
L
m/1s
0
m/3s
0
m/10s
0
If a Vario module, Order No. 33601 , is connected to the
receiver, then this screen provides a graphic display
of the data supplied by it. For more information on this
module please see the Appendix or refer to the product
on the Internet at www.graupner.de.
The meanings are as follows:
Value Explanation
ALT Current altitude
RXSQ Signal strength of the signal picked up
by the receiver in %
MAX The pre-set altitude limit relative to
the launch point; above this altitude
the transmitter emits audible warning
signals
MIN The pre-set altitude limit below the
launch point; below this altitude the
transmitter emits audible warning
signals
m/1s m/1 sec climb / descent
m/3s m/3 sec climb / descent
m/10s m/10 sec climb / descent