GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 181 | Manualshive

Page: 181 / 366

background image

•

The restart of the K2 Media Server after it is configured is complete

This task is required for NAS server functionality.

1. Verify that the K2 Media Server has restarted by opening the MS-DOS command prompt and

use the “ping” command.

2. In the K2Config application tree view, under the K2 Media Server select the File System Server

node.

The File System Server Configuration page appears.

3. Click

Check

and verify that the V: drive is shared.

Proceed as follows:

•

If you have NH servers, configure them next.

•

If you do not have NH servers, configure K2 clients and/or other iSCSI clients on the K2 SAN
next.

Configuring optional NH servers

If you have one or more optional NH K2 Media Servers, you next configure those servers. This
section applies to both NH1 (1 Gig FTP) servers and NH10GE (10 Gig FTP) servers.

NOTE: Multiple NH servers on a K2 SAN must be of the same type, either all NH1 or all NH10GE.

1. In the K2Config application tree view, select the K2 Media Server you are configuring.

2. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

02 February 2012

K2 SAN Installation and Service Manual

181

Configuring and licensing the K2 SAN

«
...
179
180
181
182
183
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Brand: Paradox Pages: 2

Brand: EAS Electric Pages: 4

Brand: EAS Electric Pages: 31

Brand: Patton electronics Pages: 12

Brand: Data Translation Pages: 62

blueplanet 87.0 TL3

Brand: Kaco Pages: 200

ILinx 485DRCI-PH

Brand: B&B Pages: 2

Brand: Xantrex Pages: 58

Brand: Mosa Pages: 48

Brand: Pro-Ject Audio Systems Pages: 3

Brand: Parallax Pages: 3

Brand: Avtech Pages: 4

Brand: Systech Corporation Pages: 6

Prizm 200750 Series

Brand: Moog Pages: 12

STORAGE PACKAGE - BUSINESS

Brand: SMA Solar Technology AG Pages: 30

Brand: OLIJU Pages: 20

Brand: Wagan Pages: 36

Brand: GME Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands