GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 236 | Manualshive

Page: 236 / 366

background image

Configure Network Configuration page - K2 client

This page configures both control and media (iSCSI) network connections.

The K2 client actually has four Gigabit Ethernet ports, but two ports are configured as a teamed
pair (the control team), while the other two ports (the media connections) are individual. The teamed
pair shares an IP address and appears on this page as a single port.

1. Verify that the top port is configured correctly.

The top port is the port over which the K2Config application is communicating. If correctly
configured, it is already assigned the control network IP address, as displayed on this page.

2. Select

Media Connection #1

and then click

Modify

.

A network configuration dialog box opens.

3. Verify or configure Media Connection #1 as follows:

•

If a basic (non-redundant) K2 SAN, verify or enter the media network IP address. Also enter
the subnet mask.

•

If a redundant K2 SAN, verify or enter an IP address for the “A” media (iSCSI) network.
Also enter the subnet mask.

4. Do one of the following:

•

If a basic (non-redundant) K2 SAN, skip to the last step in this procedure. Do not configure
Media Connection #2.

•

If a redundant K2 SAN, proceed with the next step and configure Media Connection #2.

5. Select

Media Connection #2

and then click

Modify

.

A network configuration dialog box opens.

236

K2 SAN Installation and Service Manual

02 February 2012

Configuring clients on the K2 SAN

«
...
234
235
236
237
238
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Brand: Xtreamer Pages: 2

Brand: µ-Dimension Pages: 6

Brand: Redgum Pages: 12

Brand: Schumacher Pages: 45

Brand: Tripp Lite Pages: 4

Brand: Icy Box Pages: 2

Brand: nedis Pages: 48

BNI IOL-712-000-K023

Brand: Balluff Pages: 12

Brand: Wagan Pages: 44

Brand: T+A Pages: 72

Brand: CEL-MAR Pages: 28

Brand: Rohde & Schwarz Pages: 653

AZZYRRO 3-6-ZSS-HP

Brand: ZCS Pages: 65

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology 8R

Brand: M-Audio Pages: 25

Brand: Tektronix Pages: 28

JNTHBCBA0001BEAU

Brand: TECO Pages: 98

CTRLink EIMK-100T/FT

Brand: Contemporary Controls Pages: 4

Brand: ADF Web Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands