GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 104 | Manualshive

Page: 104 / 366

background image

•

NH K2 Media Server

1. In the Interfaces list view determine the interface to configure, as follows:

•

Identify the interface with which SiteConfig is currently communicating, indicated by the
green star overlay icon. This should be the control network interface.

•

Verify that the interface over which SiteConfig is currently communicating is in fact the
interface defined for the control network in the system description. If this is not the case, you
might have the control network cable connected to the wrong interface port. The control
connection should always be the first port on the motherboard, except when you have a
loopback connection.

•

Configure the control network interface first before configuring any of the other interfaces.

•

After you have successfully configured the control network interface, return to this step to
configure each remaining interface.

•

For the K2 Media Server, do not configure the Fibre Channel interface, which is a non-IP
interface. SiteConfig does not manage this interface. It is represented in SiteConfig only to
complete the description of the K2 Media Server.

2. In the Interfaces list view, check the icon for the interface you are configuring.

If the icon has a red stop sign overlay, it indicates that current settings and planned settings do
not match or that there is some other problem. Hover over the icon to read a tooltip with
information about the problem.

104

K2 SAN Installation and Service Manual

02 February 2012

Planning and implementing a K2 SAN with SiteConfig

«
...
102
103
104
105
106
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Brand: KDS Pages: 4

Brand: T+A Pages: 64

Brand: CYP Pages: 9

IFS MC250-4T Series

Brand: Interlogix Pages: 23

Helios III Series

Brand: CNBOU Pages: 27

Brand: Cross Technologies Pages: 18

Brand: ELCART Pages: 2

Brand: TANDBERG Pages: 196

Brand: BZBGEAR Pages: 12

FRENIC-VG Series

Brand: Fuji Electric Pages: 346

Brand: Tecsun Pages: 2

Brand: HQ Power Pages: 8

Brand: Danfoss Pages: 57

Brand: Waeco Pages: 76

MultyMedia TS 1

Brand: TechniSat Pages: 91

Brand: Thinklogical Pages: 19

Brand: IMC Networks Pages: 1

HD-CONV-USB-250

Brand: Crestron Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands