GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 156

Page: 156 / 366

Configure New K2 System page 3 - Redundant K2 SAN

1. Review the information on this page and verify that you have correctly defined your K2 SAN.

For a 10G basic K2 SAN you should have the following:

•

One Gigabit Ethernet switch

•

One K2 Media Server

•

Optionally, one or more NH K2 Media Servers

•

The number and type of clients appropriate for your system.

2. Click

Finish

The Define New K2 Storage System wizard closes.

Your storage system appears in the tree view of the K2Config application.

Next, configure the server.

Configuring server A - Part 1

1. In the K2Config application tree view, select

[K2Server1]

2. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

156

K2 SAN Installation and Service Manual

02 February 2012

Configuring and licensing the K2 SAN

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Search results

Summary of Contents for K2 BASECAMP EXPRESS

Reviews:

Related manuals for K2 BASECAMP EXPRESS

Brands by name

Popular brands

GRASS VALLEY K2 BASECAMP EXPRESS, Installation And Service Manual

Search results

Summary of Contents for K2 BASECAMP EXPRESS

Reviews:

Related manuals for K2 BASECAMP EXPRESS

Brands by name

Popular brands