manualshive.com logo in svg

GRASS VALLEY K2 BASECAMP EXPRESS, Installation And Service Manual

"Upgrade Instructions and user manual for the GRASS VALLEY K2 BASECAMP EXPRESS are now available for free download at our website. Discover step-by-step guidance and essential information to enhance your product experience. Simply visit manualshive.com to access these valuable resources and optimize the functionality of your K2 BASECAMP EXPRESS."

Share
Download
background image

Power off K2 RAID............................................................................................................................245
Power off remaining K2 SAN devices................................................................................................245

Powering on the K2 SAN......................................................................................................................245

Basic K2 SAN power on procedure...................................................................................................246
Redundant K2 SAN power on procedure..........................................................................................247
Nearline K2 SAN power on procedure..............................................................................................249
Powering on the HP ProCurve switch...............................................................................................250
Powering on the control point PC......................................................................................................250

Failover behaviors.................................................................................................................................250

Pre-failover behavior.........................................................................................................................251
Control Team failover behavior..........................................................................................................251
K2 client media (iSCSI) connection failover behavior........................................................................252
K2 Media Server failover behavior....................................................................................................254
K2 Media Server failover with Control team failover behavior...........................................................255

Chapter 10: Description of K2 SAN Devices.........................................................................257

Device terminology...............................................................................................................................258
Control point PC description.................................................................................................................258
K2 Ethernet switch description.............................................................................................................259

K2 Ethernet switch specifications......................................................................................................259

K2 Media Server description.................................................................................................................260

K2 Media Server specifications.........................................................................................................260

NH K2 Media Server.............................................................................................................................261

NH K2 Media Server specifications...................................................................................................261

K2 RAID storage description................................................................................................................261

Chapter 11: Overview of K2 Storage Tools...........................................................................263

About SiteConfig...................................................................................................................................264

Opening SiteConfig...........................................................................................................................264
SiteConfig main window....................................................................................................................264

K2Config...............................................................................................................................................265

Opening the K2Config application.....................................................................................................266

Server Control Panel.............................................................................................................................267
Storage Utility for K2 SAN.....................................................................................................................268

About RANKs and LUNs in Storage Utility........................................................................................269

NetCentral.............................................................................................................................................269
Windows Remote Desktop Connection................................................................................................270

Accessing Remote Desktop Connection...........................................................................................270

Chapter 12: Administering and maintaining the K2 SAN....................................................271

Passwords and security on Grass Valley systems................................................................................272

About application security on the K2 SAN........................................................................................272

Modifying K2 SAN settings...................................................................................................................273

Accessing K2 SAN features..............................................................................................................274
About SiteConfig and K2Config settings...........................................................................................274
Renaming a K2 SAN.........................................................................................................................276
Adding devices to a K2 SAN.............................................................................................................276
Removing a K2 SAN.........................................................................................................................278
Accessing a K2 SAN from multiple PCs............................................................................................278
Taking a K2 SAN offline....................................................................................................................279
Bringing a K2 SAN online..................................................................................................................279
Viewing iSCSI assignments..............................................................................................................280
Using reference files..........................................................................................................................280

Managing redundancy on a K2 SAN....................................................................................................281

Identifying current primary/backup K2 Media Servers......................................................................281
Triggering an intentional failover........................................................................................................283

8

K2 SAN Installation and Service Manual 

02 February 2012

Contents

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Kaco blueplanet 15.0 TL3 Quick Manual preview
blueplanet 15.0 TL3
Brand: Kaco Pages: 188
Kaiser Baas KBA03026 Troubleshooting Manual preview
KBA03026
Brand: Kaiser Baas Pages: 3
OST OmniConverter GPoE+/S User Manual preview
OmniConverter GPoE+/S
Brand: OST Pages: 10
NF DF 1906 Instruction Manual preview
DF 1906
Brand: NF Pages: 96
CYP CM-388 Operation Manual preview
CM-388
Brand: CYP Pages: 16
Whistler GO AC PP750 Owner'S Manual preview
GO AC PP750
Brand: Whistler Pages: 15
APsystems DS3 Series Installation Manual preview
DS3 Series
Brand: APsystems Pages: 22
YASKAWA CIMR-XC2 Series Instruction Manual preview
CIMR-XC2 Series
Brand: YASKAWA Pages: 77
FireBird CPK 7210 N Manual preview
CPK 7210 N
Brand: FireBird Pages: 44
E-matic EM304CAMB Manual preview
EM304CAMB
Brand: E-matic Pages: 22
Pyramid 5 KW 3 Phase User & Installation Manual preview
5 KW 3 Phase
Brand: Pyramid Pages: 39
ADF Web HD67950-B2 User Manual preview
HD67950-B2
Brand: ADF Web Pages: 36
Lawmate PV-500EVO2 User Manual preview
PV-500EVO2
Brand: Lawmate Pages: 34
PLAYNETICS Al-Mu'allim AM-RD2 User Manual preview
Al-Mu'allim AM-RD2
Brand: PLAYNETICS Pages: 21
S4A WIEGAND-Ethernet Manual preview
WIEGAND-Ethernet
Brand: S4A Pages: 23
Trace Engineering LEGEND I Datasheet preview
LEGEND I
Brand: Trace Engineering Pages: 2
Nyrius NIPV800 User Manual preview
NIPV800
Brand: Nyrius Pages: 11
Ensemble Designs Bright Eye 91 User Manual preview
Bright Eye 91
Brand: Ensemble Designs Pages: 37

Brands by name

Popular brands

Load more brands