GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 343 | Manualshive

Page: 343 / 366

background image

iSCSI extended (redundant FSMs)

RAID Storage

GigE Fabric

K2 SAN-attached client systems

FSM/Bridge

K2 Media Servers

FTP/Bridge

K2 Media Servers

Fibre Channel Fabric

Control Point PC

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

!

K2

MEDIA SERVER

!

K2

MEDIA SERVER

!

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

Key to illustrated cable paths:

Gigabit Ethernet carrying real-time media

Fibre Channel carrying real-time media

Gigabit Ethernet carrying traffic that is not

real-time media

A black/gray pair denotes redundant cables

This system differs from the Level 3R system as follows:

•

A Fibre Channel switch fabric, comprised of one or more Fibre Channel switches, is interposed
between K2 Media Servers and the RAID Storage devices. This allows more RAID Storage
devices to be connected, which provides higher bandwidth and more storage space.

•

Additional FTP/Bridge K2 Media Servers are added, providing additional iSCSI bridges to
support more clients and higher bandwidth clients.

Guidelines for this system are as follows:

•

The Fibre Channel switch fabric must be zoned.

Related Topics

Fibre Channel switch zoning

02 February 2012

K2 SAN Installation and Service Manual

343

Custom K2 SAN systems

«
...
341
342
343
344
345
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Brand: Daikin Pages: 4

Brand: Unipower Pages: 19

Brand: B&B Electronics Pages: 13

Brand: Growatt Pages: 45

Brand: Sylvania Pages: 28

Brand: A-TS TECHNOLOGY Pages: 87

Brand: Fischer Panda Pages: 214

Brand: Delta Pages: 1

Brand: DAD Pages: 31

Brand: Rohde & Schwarz Pages: 653

Brand: YOKOGAWA Pages: 84

MOB31-12HFN1-QRD0GW

Brand: Midea Pages: 65

Brand: UCView Pages: 4

Brand: Synthrotek Pages: 5

Brand: Patton electronics Pages: 20

LaCinema Premier

Brand: LaCie Pages: 24

Brand: Geotech Pages: 48

Brand: Kaco Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands