GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 25 | Manualshive

Page: 25 / 366

background image

Quick Start Guides

The Quick Start Guide is a printed document, shipped in the product packaging with K2 Summit/Solo
systems and K2 Dyno Replay Controllers. The Quick Start Guide provides step-by-step installation
instructions for basic installation and operation of the product.

K2 Storage Cabling Guide

The K2 Storage Cabling Guide is a printed document, shipped in the product packaging with the
primary RAID storage chassis. The cabling guide provides instructions for K2 Storage Area Network
(SAN) cabling and external configuration. The cabling guide provides instructions for each level
of K2 SAN and covers both redundant and basic (non-redundant) systems. It also provides instructions
for connecting direct-connect external RAID storage to K2 Summit systems.

K2 Documentation Set

Except for the release notes, the full set of support documentation, including this manual, is available
in the K2 or K2/STRATUS Documentation Set. You can find the Documentation Set on the Grass
Valley website. The following URL allows you to browse by K2 software version:

http://www.grassvalley.com/dl/k2_summit

You can also find the Documentation Set on the USB Recovery Flash drive that ships with your K2
Summit/Solo system.

The Documentation Set includes the following K2 product documents:

Provides instructions for configuring and operating the media channels
of product.

K2 AppCenter User
Manual

The Quick Start Guide provides step-by-step installation instructions
for basic installation and operation of the product.

Quick Start Guides

Contains the product specifications and instructions for modifying
system settings.

K2 System Guide

Contains information on servicing and maintaining the K2 product.

K2 Service Manuals

Contains installation, configuration, and maintenance procedures for
shared storage options.

K2 SAN Installation and
Service Manual

The cabling guide provides instructions for K2 Storage Area Network
(SAN) cabling and external configuration. The cabling guide provides
instructions for each level of K2 SAN and covers both redundant and
basic (non-redundant) systems. It also provides instructions for
connecting direct-connect external RAID storage to K2 Summit
systems.

K2 Storage Cabling Guide

There is an Instruction Manual for each type of RAID storage device
that can be a part of a K2 SAN. These manuals contain procedures for
configuring and servicing the device.

RAID Instruction Manuals

Contains information on configuring and servicing the Fibre Channel
switch.

Fibre Channel Switch
Installation Manual

02 February 2012

K2 SAN Installation and Service Manual

25

Preface

«
...
23
24
25
26
27
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

LaCinema Black RECORD

Brand: LaCie Pages: 5

Brand: Yosin Pages: 17

Brand: Orban Pages: 90

CIMR-XC2 Series

Brand: YASKAWA Pages: 77

BLUESTREAM DA44AU

Brand: Dante Pages: 12

Brand: Briggs & Stratton Pages: 60

Brand: CEL-MAR Pages: 16

Brand: Cable-Tronix Pages: 4

WinFast Wi2000D

Brand: Leadtek Pages: 2

Brand: PRIZM Pages: 7

Brand: GALCO Pages: 8

Atlona OmniStream 122

Brand: Panduit Pages: 12

Brand: Jaguar King Pages: 54

SinePower MSI212

Brand: Waeco Pages: 220

Brand: Naxa Pages: 20

Brand: iBasso Audio Pages: 64

Brand: Bladelius Pages: 6

Brand: Transition Networks Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands