GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 223 | Manualshive

Page: 223 / 366

background image

Configuring NH server B

Prerequisites:

•

Server A is configured

•

The restart of server A after it is configured is complete

On nearline systems, both NH K2 Media Servers are identical, with the exception that only one
server can be the active media file system server at any time. For this reason the K2Config application
embeds the configuration and start of the media file system into the wizard when you configure the
first NH K2 Media Server, as in the previous procedure. That server is now the acting media file
system server. You can now configure the remaining server using the following procedure.

1. Verify that server A has restarted by opening the MS-DOS command prompt and use the “ping”

command.

2. In the K2 System Configuration application tree view, select the K2 Media Server you are

configuring as server B.

3. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

Configure Define Server Roles page - NH server

1. Enter the name for the K2 Media Server, as currently configured on the machine.

For Nearline server roles, selections are disabled. Leave SNFS file system server, FTP server,
and NAS server selected.

The wizard does not allow you to select Media Database Server. There is no Media Database
Server in a nearline system.

2. Click

Next

.

02 February 2012

K2 SAN Installation and Service Manual

223

Configuring and licensing the K2 SAN

«
...
221
222
223
224
225
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Brand: Danfoss Pages: 68

Brand: Daikin Pages: 21

Brand: CYP Pages: 38

Brand: Vicon Pages: 18

Brand: American Audio Pages: 2

Brand: M-Audio Pages: 20

Brand: MAGIRA Pages: 58

Brand: LevelOne Pages: 9

Brand: RME Audio Pages: 68

ELinx EIR-G-SFP-T

Brand: B&B Electronics Pages: 2

OPS500-501 Series

Brand: AXIOMTEK Pages: 54

Brand: YOKOGAWA Pages: 84

Brand: Turbo Energy Pages: 33

RB-4KHDMI Series

Brand: ROBOfiber Pages: 2

Brand: Blackmagicdesign Pages: 521

Brand: Hitachi Pages: 20

Brand: Hitachi Pages: 35

Brand: Hitachi Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands