GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 163 | Manualshive

Page: 163 / 366

background image

3. In the Storage Utility main window, identify bound RANKs and unbound disks by their placement

in the hierarchy of the tree view. In the following illustration, disk numbers are represented by
“XX”.

Redundant systems store file system metadata files and journal files on the primary RAID chassis.
The first six disk slots in the chassis are dedicated for metadata/journal files. In the first five slots
are five metadata/journal disks. The sixth slot is filled with a blank. Two disks are bound as a
RAID 1 RANK for metadata storage and two disks are bound as a RAID 1 RANK for journal
storage. The fifth disk is bound as a Hot Spare for the other four metadata/journal disks. The
remaining six disks in the primary RAID chassis and all disks in Expansion chassis are for media
storage. Media storage disks are bound as RAID 5 or RAID 6 in RANKs consisting of six disks
each.

View disk properties and identify the four disks you will use for the metadata/journal RAID 1
RANKs, the one metadata/journal Hot Spare disk, any other disks that you intend to use for Hot
Spares, and the remainder of the disks that are available for media storage. Make sure you select
disks appropriately as you bind disks in the remainder of this procedure.

02 February 2012

K2 SAN Installation and Service Manual

163

Configuring and licensing the K2 SAN

«
...
161
162
163
164
165
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

VLT DeviceNet MCA 104

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 138

Brand: Danfoss Pages: 108

Brand: Danfoss Pages: 149

MIXHITS iSTREAM2

Brand: ESS Pages: 4

Brand: ScienTECH Pages: 12

Brand: Radial Engineering Pages: 18

Brand: Lawmate Pages: 34

Brand: I-Tech Pages: 16

Brand: GoMax Electronics Pages: 12

Brand: Optelecom-nkf Pages: 4

Q.HOME+ ESS HYB-G2

Brand: Q CELLS Pages: 60

BRAVO ST 230 VAC

Brand: Helios Power Solutions Pages: 39

Compressor Drive CD302

Brand: Danfoss Pages: 28

Brand: Stanley Pages: 7

Brand: Saftronics Pages: 101

LokPilot Fx micro V3.0

Brand: Esu Pages: 72

Brand: AIMS Power Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands