manualshive.com logo in svg

GigaDevice Semiconductor GD32L23 Series, User Manual

Share
Download
GigaDevice Semiconductor GD32L23 Series User Manual Download Page 70

                                                                                                                   

GD32L23x User Manual

 

70 

 

 

default.  The  COREOFF1  domain  needs  to  be  powered  on  when  using  modules  in  the 

COREOFF1  domain.  The  COREOFF1  domain  can  be  powered  off  in  order  to  reduce  the 

power consumption in Run/Run1/Run2 mode. To further reduce power consumption in low-

power mode (Sleep/Sleep1/Sleep2/Deep-sleep/Deep-sleep1/Deep-sleep2), the COREOFF1 

domain can be powered off before entering the low-power mode. 

The COREOFF1 power domain includes CAU module. 

COREOFF0 power domain 

The COREOFF0 power domain is power-off  when  enter Deep-sleep2 mode and power-on 

when exit Deep-sleep2 mode. 

The COREOFF0 power domain includes the following module: 

CPU/BUS/ADC/CMP/CRC/CTC/DAC/DMA/I2C0/I2C1/SLCD/TRNG/SPI0/SPI1/TIMER1/TIM

ER2/TIMER5/TIMER6/TIMER8/TIMER11/USART0/USART1/USART3/USART4/USBD. 

Note: 

The  CPU  registers  can  be  retention  or  not  by  configuring  NRRD2  bit  in  PMU_CTL1 

register when enter/exit Deep-sleep2 mode. 

3.3.4. 

Power saving modes 

After a system reset or a power reset, the GD32L23x MCU operates at full function and all 

power  domains  are  active.  Users  can  achieve  lower  power  consumption  through  slowing 

down  the  system  clocks  (HCLK,  PCLK1,  and  PCLK2)  or  gating  the  clocks  of  the  unused 

peripherals.  Besides,  ten  power  saving  modes  are  provided  to  achieve  even  lower  power 

consumption, they are Run, Run1, Run2, Sleep mode, Sleep 1 mode, Sleep2 mode, Deep-

sleep mode, Deep-sleep 1 mode, Deep-sleep 2 mode and Standby mode.   

Run mode 

After system reset/ power reset or wakeup from standby mode, the MCU enters Run mode. 

And the NPLDO (normal power LDO) works in 1.1V mode. 

Run1 mode

When in Run mode, the NPLDO should be selected as 0.9V by configuring the LDOVS bits 

in PMU_CTL0. In this mode, the system clock frequency should not exceed 16MHz. 

Run2 mode 

When in Run mode or Run1 mode, the NPLDO can be selected as 0.9V by configuring the 

LDOVS bits in PMU_CTL0. The LDNP in PMU_CTL0 register should be configured to select 

the low-dirver mode. In this mode, the system clock frequency should not exceed 2MHz. 

Summary of Contents for GD32L23 Series
































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands