manualshive.com logo in svg

GigaDevice Semiconductor GD32L23 Series, User Manual

Share
Download
GigaDevice Semiconductor GD32L23 Series User Manual Download Page 545

                                                                                                                   

GD32L23x User Manual

 

545 

 

 

between them are described below. 

In  slave  mode,  the  slave  has  to  be  enabled  before  the  external  master  starts  the 

communication. The reception sequence begins when the external master sends the clock 

and when the I2S_WS signal indicates a start of the data transfer. In slave mode, I2SCH is 

sensitive to the I2S_WS signal coming from the external master. 

In order to disable I2S, it is mandatory to clear the I2SEN bit immediately after receiving the 

last RBNE. 

22.9.4. 

DMA function 

DMA function is the same as SPI mode. The only difference is that the CRC function is not 

available in I2S mode. 

22.10. 

I2S interrupts 

22.10.1. 

Status flags 

There  are  four  status  flags  implemented  in  the  SPI_STAT  register,  including  TBE,  RBNE, 

TRANS and I2SCH. The user can use them to fully monitor the state of the I2S bus.   

 

Transmit buffer empty flag (TBE) 

This bit is set when the transmit buffer is empty, the software can write the next data to the 

transmit buffer by writing the SPI_DATA register. 

 

Receive buffer not empty flag (RBNE) 

This bit is set when receive buffer is not empty, which means that one data is received and 

stored in the receive buffer, and software can read the data by reading the SPI_DATA register. 

 

I2S transmitting ongoing flag (TRANS) 

TRANS is a status flag to indicate whether the transfer is ongoing or not. It is set and cleared 

by hardware and not controlled by software. This flag will not generate any interrupt. 

 

I2S channel side flag (I2SCH) 

This flag indicates the channel side information of the current transfer and has no meaning in 

PCM mode. It is updated when TBE rises in transmission mode or RBNE rises in reception 

mode. This flag will not generate any interrupt. 

22.10.2. 

Error conditions 

There are three error flags: 

 

Transmission underrun error flag (TXURERR) 

Summary of Contents for GD32L23 Series
































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands