manualshive.com logo in svg

Fujitsu MB91150 Series, Hardware Manual, Page: 63 / 512

Share
Download
Fujitsu MB91150 Series Hardware Manual Download Page 63

47

CHAPTER 3  MEMORY SPACE, CPU AND CONTROL UNIT

3.7

Overview of Instructions

In addition to the general RISC instruction system, the FR series supports logical 
operation instructions and bit operation instructions that were optimized for insertion, 
and direct addressing instructions. Each instruction is at least 16 bits long (some 
instructions are 32 or 48 bits long), which makes for excellent memory use efficiency.
The instruction sets can be divided into the following functional groups:
• Arithmetic operation
• Load and store
• Branch
• Logical operation and bit operation
• Direct addressing
• Others

■

Overview of Instructions

❍

Arithmetic operation

This functional group includes the standard arithmetic operation instructions (addition,
subtraction, and comparison) and shift instructions (logical shift and arithmetic operation shift).
The operations for addition and subtraction that are supported include 

multi-word length operations with carry-over, and operations in which flag values that are used
to support address calculation remain unchanged.

In addition, multiplication instructions of 32 bits x 32 bits and of 16 bits x 16 bits and the step
division instruction of 32 bits divided by 32 bits are provided.

The immediate data transfer instructions for setting immediate data in registers and the register-
to-register transfer instructions are also provided.

The arithmetic operation instructions can use all of the general-purpose registers and
multiplication and division registers in the CPU.

❍

Load and store

The load and store instructions are used for read and write-accesses to external memory. They
are also used for read and write-accesses to the peripheral circuit (I/O) on the chip. 

The load and store instructions support three types of access lengths: byte, half word and word.
In addition to direct memory addressing between general registers, some instructions support
register indirect memory addressing with displacement or with register increment and
decrement.

❍

Branch

This functional group includes branch, call, interrupt, and return instructions. Some branch
instructions have delay slots and others do not, which allows optimization in accordance with
usage.

The branch instructions are detailed later.

Summary of Contents for MB91150 Series

































































































































































































































































































































































































































































































































Reviews:

No comments