manualshive.com logo in svg

Fujitsu MB91150 Series, Hardware Manual, Page: 323 / 512

Share
Download
Fujitsu MB91150 Series Hardware Manual Download Page 323

307

CHAPTER 15  UART

The following describes the function of each block.

❍

Clock selector

The clock selector selects the send and receive clocks from the dedicated baud-rate generator,
external input clock, and internal clock (clock supplied from the 16-bit reload timer).

❍

Receive control circuit

The receive control circuit consists of the receive-bit counter, start-bit detection circuit, and
receive-parity counter. The receive-bit counter counts receive data and, after reception of one
data unit is completed, generates a receive-interrupt request in accordance with the set-data
length. The start-bit detection circuit detects a start bit in the serial-input signal and, if a start bit
is detected, writes data to the SIDR0-3 register while shifting in accordance with the specified
transfer speed. The receive-parity counter calculates the parity of receive data.

❍

Send-control circuit

The send-control circuit consists of the send-bit counter, send-start circuit, and send-parity
counter. The send-bit counter counts send data and, when sending of one data unit is
completed, generates a send-interrupt request in accordance with the set data length. The
send-start circuit starts a send operation when SODR0-3 is written. The send-parity counter
calculates the parity of send data when parity is enabled.

❍

Receive-shift register

The receive-shift register fetches the receive data, which is input from the SIN pins, while
shifting the data in steps of one bit. When reception terminates, the receive data is transferred
from the receive-shift register to the SIDR0-3 register.

❍

Send-shift register

The send-shift register transfers the data written in SODR0-3 to the send-shift register and
outputs the data to the SOT pins while shifting the data in steps of one bit.

❍

Mode register 1 (SMR0-3)

This register selects the operation mode, selects the clock-input source, sets the dedicated
baud-rate generator, and selects the clock rate (clock divide-by value) for using the dedicated
baud-rate generator. It also sets serial data output to pin enabled or disabled, and sets clock
output to pin enabled or disabled.

❍

Control register 1 (SCR0-3)

This register sets parity to enabled or disabled, selects the parity, sets the stop-bit length, sets
the data length, selects the frame data format in mode 1, and clears the flag. It also sets
sending to enabled or disabled, and sets receiving to enabled or disabled.

❍

Status register 1 (SSR0-3)

This register checks the send, receive and error statuses, and sets send- and receive-interrupt
request enabled/disabled.

❍

Input-data register 1 (SIDR0-3)

This register retains the receive data. Serial input is converted and stored in this register.

❍

Output-data register 1 (SODR0-3)

This register sets the send data. The data written in this register undergoes parallel-to-serial
conversion and is output.

Summary of Contents for MB91150 Series

































































































































































































































































































































































































































































































































Reviews:

No comments