manualshive.com logo in svg

Fujitsu MB91150 Series, Hardware Manual, Page: 49 / 512

Share
Download
Fujitsu MB91150 Series Hardware Manual Download Page 49

33

CHAPTER 3  MEMORY SPACE, CPU AND CONTROL UNIT

3.2

CPU Architecture

The FR CPU is a high-performance core employing RISC architecture and using high-
level function instructions for insertion.

■

Features

❍

Use of the RISC architecture

❍

Basic instructions, one instruction for one cycle

❍

32-bit architecture

•

32-bit general-purpose registers: 16

❍

Linear 4-gigabyte memory space

❍

Multiplier mounted

•

Multiplication of 32 bits x 32 bits: 5 cycles

•

Multiplication of 16 bits x 16 bits: 3 cycles

❍

Enforced interrupt processing functions

•

High-speed response (6 cycles)

•

Multiple interrupts supported

•

Level mask function (16 levels)

❍

Enforced I/O operation instructions

•

Memory-to-memory transfer instructions

•

Bit processing instructions

❍

High code efficiency

•

Word length of a basic instruction: 16 bits

❍

Low power consumption

•

Sleep mode and stop mode

Summary of Contents for MB91150 Series

































































































































































































































































































































































































































































































































Reviews:

No comments