Fujitsu fi-7300NX Operator'S Manual Download

Page: 124 / 321

HINT

If it is difficult to clean, use a cotton swab.

Feed Roller (× 2)/Eject Roller (× 2)

The power must be turned on to rotate the feed/eject rollers for cleaning.

Plug in the power cable and turn on the scanner.
For details, refer to

How to Turn the Power ON (page 56)

On the touch screen, press

→ [Cleaning & Maintenance] → [Cleaning] → [Cleaning

Wipe].
The [Cleaning Wipe] screen is displayed.

ATTENTION

Do not start scanning with an image scanning application during cleaning.

Open the ADF.
For details, refer to

How to Open the ADF (page 63)

Daily Care

124

Summary of Contents for fi-7300NX


































































































































































































































































































































Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands

Fujitsu fi-7300NX, Operator'S Manual

Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands