Fujitsu fi-7300NX Operator'S Manual Download Page 268 | Manualshive

Page: 268 / 321

background image

Clearing the Sheet Counters

When you have replaced or cleaned a consumable part, clear the corresponding counter.

1

Start up the Software Operation Panel.
For details, refer to

Starting Up the Software Operation Panel (page 248)

2

From the list on the left, select [Device Setting] and click the [Clear] button for [After cleaning] when
cleaning is performed or click the [Clear] button for the consumable that you replaced.

The counter is reset to "0".

3

Click the [OK] button.

A message window appears.

4

Click the [OK] button.

The settings are saved.

Scanner Settings (Software Operation Panel)

268

«
...
266
267
268
269
270
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

Brand: Unitech Pages: 14

ArtixScan DI 5230

Brand: Microtek Pages: 16

Brand: Pacific Image Electronics Pages: 19

Brand: Radio Shack Pages: 16

CyberScanner P500

Brand: Easy Pix Pages: 30

Brand: Datalogic Pages: 2

Brand: ION Pages: 40

Brand: Kodak Pages: 43

8412447 - I55 - Document Scanner

Brand: Kodak Pages: 93

Digital Science 9520

Brand: Kodak Pages: 139

Brand: VORMOR Pages: 11

ScanStation P30

Brand: Leica Geosystems Pages: 12

Pannoramic SCAN II 2.0

Brand: 3DHISTECH Ltd. Pages: 142

SafeScan SG1004A

Brand: Safe-grain Pages: 2

Brand: Xerox Pages: 132

Brand: Radio Shack Pages: 64

SeeLevel 710-JS

Brand: Garnet Pages: 12

Imageformula scanfront 220

Brand: Canon Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands