2-16
Chapter 2
3. Function Explanation
■
E01 X1 terminal function
to
■
E09 X9 terminal function
Each function of digital input terminals (X1 to X9) can be set
as codes.
E01
X1 FUNC
3.2 Extension Terminal Functions
E02
X2 FUNC
E03
X3 FUNC
E04
X4 FUNC
E05
X5 FUNC
E06
X6 FUNC
E07
X7 FUNC
E08
X8 FUNC
E09
X9 FUNC
NOTE:
Data numbers which are not set in the functions from E01 to E09
or E05, are assumed to be inactive.
The frequency can be switched to a preset frequency in
function codes C05 to C19 by switching the external digital
input signal. Assign values
0
to
3
to the target digital input
terminal. The combination of input signals determines the
frequency.
Multistep frequency selection
Multistep frequency selection
: 0, 1, 2, 3
Combination of set
value input signals
3
2
1
0
(SS8)
(SS4) (SS2) (SS1)
Frequency selected
off
off
off
on
C05 Multistep Hz1
off
off
on
off C06 Multistep Hz2
off
off
on
on
C07 Multistep Hz3
off
on
off
off C08 Multistep Hz4
off
on
off
on
C09 Multistep Hz5
off
on
on
off C10 Multistep Hz6
off
on
on
on
C11 Multistep Hz7
on
off
off
off C12 Multistep Hz8
on
off
off
on
C13 Multistep Hz9
on
off
on
off C14 Multistep Hz10
on
off
on
on
C15 Multistep Hz11
on
on
off
off C16 Multistep Hz12
on
on
off
on
C17 Multistep Hz13
on
on
on
off C18 Multistep Hz14
on
on
on
on
C19 Multistep Hz15
The acceleration and deceleration time can be switched to a
preset time in function codes E10 to E15 by switching the
external digital input signal. Assign values
“4”
and
“5”
to the
target digital input terminal. The combination of input signals
determines the acceleration and deceleration times.
Acceleration and deceleration time selection
:4,5
This function is used for 3-wire operation. The FWD or REV
signal is self-held when HLD is on, and the self-hold is cleared
when HLD is turned off. To use this HLD terminal function,
assign value
“6”
to the target digital input terminal.
Three-wire operation stop command [HLD]
: 6
C05 to C19
Setting range
G11S:
0.00 to 400.00Hz
P11S:
0.00 to 120.00Hz
Combination of set
value input signals
5
4
(RT2)
(RT1)
off
off
F07 Acceleration time 1
F08 Deceleration time 1
off
on
E10 Acceleration time 2
E11 Deceleration time 2
on
off
E12 Acceleration time 3
E13 Deceleration time 3
on
on
E14 Acceleration time 4
E15 Deceleration time 4
F07, F08
E10 to E15
Setting range
0.01 to 3600s
Acceleration and deceleration times
selected
0, 1, 2, 3 Multistep frequency selection (1 to 15 steps)
4, 5
Acceleration and deceleration time selection (3 steps)
6
3-wire operation stop command [HLD]
7
Coast-to-stop command [BX]
8
Alarm reset [RST)
9
Trip command (External fault) [THR]
10
Jogging operation [JOG)
11
Freq. set 2/Freq. set 1 [Hz2/Hz1]
12
Motor 2/motor 1 [M2/M1]
13
DC brake command [DCBRK]
14
Torque limiter 2/Torque limiter 1 [TL2/TL1]
15
Switching operation between line and inverter (50Hz)
[SW50]
16
Switching operation between line and inverter (60Hz)
[SW60]
17
UP command [UP]
18
DOWN command [DOWN]
19
Write enable for KEYPAD (data change permission)
[WE-KP]
20
PID control cancel [Hz/PID]
21
Inverse mode changeover (terminals 12 and C1) (IVS)
22
Interlock signal for 52-2 [IL]
23
Torque control cancel [Hz/TRQ]
24
Link enable (RS-485: standard, Bus: option) [LE]
25
Universal DI [U-DI]
26
Pick up start mode [STM]
27
SY-PG enable [PG/Hz]
28
Synchronization command [SYC]
29
Zero speed command [ZERO]
30
Forced stop command [STOP1]
31
Forced stop command with Deceleration time 4 [STOP2]
32
Pre-exciting command [EXITE]
Set value
Function
Chapter02J(P6˜25).p65
07.8.9, 12:26
Page 16
Adobe PageMaker 6.5J/PPC
Summary of Contents for FRENIC5000G11S Series
