FujiFilm FRENIC5000G11S Series, Technical Information

Page: 18 / 236

1-12
Chapter 1
2. Common Specifications
The function marked can be set while the inverter is running. Other functions must be set while the inverter is
stopped.
Function
Setting range Unit
Min. Factory setting
Remarks
Code Name LCD monitor unit 30HP 40HP
F23
Starting frequency (Freq.)
F23 START Hz 0.1 to 60.0Hz
F24 (Holding time) F24 HOLDING t 0.0 to 10.0s
F25 Stop frequency F25 STOP Hz 0.1 to 6.0Hz
F26
Motor sound (Carrier freq.)
F26 MTR SOUND
0.75-15kHz 0.75-10kHz 0.75-6kHz
G11S
-75HP 100HP –
P11S
-30HP 40-100HP 125HP
F27 (Sound tone) F27 MTR TONE 0 : Level 0
1 : Level 1
2 : Level 2
3 : Level 3
F30 FMA (Voltage adjust) F30 FMA V-ADJ 0 to 200%
F31 (Function) F31 FMA FUNC 0 : Output frequency 1 (Before slip compensation)
1 : Output frequency 2 (After slip compensation)
2 : Output current
3 : Output voltage
4 : Output torque
5 : Load factor
6 : Input power
7 : PID feedback value
8 : PG feedback value
9 : DC link circuit voltage
10 : Universal AO
F33 FMP (Pulse rate) F33 FMP PULSES 300 to 6000 p/s (at full scale)
F34 (Voltage adjust) F34 FMP V-ADJ 0% : Pulse rate output (50% duty)
1 to 200% : Voltage adjust : 2670 p/s (duty adjust)
F35 (Function) F35 FMP FUNC 0 : Output frequency 1 (Before slip compensation)
1 : Output frequency 2 (After slip compensation)
2 : Output current
3 : Output voltage
4 : Output torque
5 : Load factor
6 : Input power
7 : PID feedback value
8 : PG feedback value
9 : DC link circuit voltage
10 : Universal AO
F36 30RY operation mode F36 30RY MODE 0 : The relay(30) excites on trip mode
1 : The relay(30) excites on normal mode
F40
Torque limiter 1
(Driving) F40 DRV TRQ 1 G11S : 20 to 200, 999% (999: No limit) *2)
P11S : 20 to 150, 999% (999: No limit)
F41 (Braking) F41 BRK TRQ 1 G11S : 0 (Automatic deceleration control),
20 to 200, 999% (999: No limit) *2)
P11S : 0 (Automatic deceleration control),
20 to 150, 999% (999: No limit)
F42 Torque vector control 1 F42 TRQVECTOR1 0 : Inactive
1 : Active
Sets the frequency at stopping.
*
In case of VT use, carrier
frequency should be adjusted
depending on capacity
Four types of tone can be
selected.
This setting is effective when
the carrier frequency "F26" is
set at 7kHz or lower.
This selection can be made
at 7kHz or higher, but the
tone does not change.
About 0 and 1
Percent indication based on
inverter rated voltage
About 0 and 1
Hz 0.1 0.5
s 0.1 0.0
Hz 0.1 0.2
kHz 1 2
- - 0
% 1 100
- - 0
p/s 1 1440
% 1 0
- - 0
- - 0
% 1 999
% 1 999
- - 0
1:Output frequency 2
0:Output frequency 1
Setting
value
KEYPAD
panel
Slip compensation
amount
Inverter
M
1:Output frequency 2
0:Output frequency 1
Setting
value
KEYPAD
panel Slip compensation
amount
Inverter
M
Extension Terminal Functions
Function
Setting range Unit
Min. Factory setting
Remarks
Code Name LCD monitor unit 30HP 40HP
E01 X1 terminal function E01 X1 FUNC Selects from the following items.
E02 X2 terminal function E02 X2 FUNC
E03 X3 terminal function E03 X3 FUNC
E04 X4 terminal function E04 X4 FUNC
E05 X5 terminal function E05 X5 FUNC
E06 X6 terminal function E06 X6 FUNC
E07 X7 terminal function E07 X7 FUNC
E08 X8 terminal function E08 X8 FUNC
E09 X9 terminal function E09 X9 FUNC
0 : [SS1]
1 : Multistep freq. select (1 to 4bit) [SS2]
2 : (16 steps) [SS4]
3 : [SS8]
4 : 4 steps of ACC/DEC time [RT1]
5 : selectioin (1 to 2bit) [RT2]
6 : 3-wire operation stop command [HLD]
7 : Coast-to-stop command [BX]
8 : Alarm reset [RST]
9 : Trip command (External fault) [THR]
10 : Jogging operation [JOG]
11 : Freq. set. 2 / Freq. set. 1 [Hz2/Hz1]
12 : Motor 2 / Motor 1 [M2/M1] 12: Switches motor
parameters to motor 2
when this signal is on.
- - 0
- - 1
- - 2
- - 3
- - 4
- - 5
- - 6
- - 7
- - 8








Chapter01J(P6˜18).p65
07.8.9, 11:53 Page 12
Adobe PageMaker 6.5J/PPC