FujiFilm FRENIC5000G11S Series, Technical Information

Page: 201 / 236

Chapter 6
2. FRENIC5000G11S/P11S Series
6-19
6
■
Function setting value (Recommended: G11S)
Other than the above functions, some of the basic functions such as base frequency, maximum frequency, acceleration/deceleration time, and
motor characteristics parameters should be set.
■
Tips
1. PATTERN operation enabled
• PATTERN operation can be set in seven stages (stages 1 to
7). The operating time (0.00 to 6000 seconds) for each
stage, rotating direction (forward or reverse), acceleration
and deceleration times, and multistep frequencies (steps 1 to
7) can be set. If the operation pattern has been decided, this
function greatly simplifies the configurations of the external
circuits and devices.
2. Measures for reducing radio noise
• This low-noise inverter switches its main circuits at high
speed. At locations where radio waves are weak, therefore,
radio noise can occur due to the effect of the wiring on the
load side. We recommend that you install a ferrite ring for
reducing radio noise (ACL-40B or ACL-75B) to reduce radio
noise, use metal conduits for wiring, and ground the control
panel, motor, and conduits using lower resistance values.
3. Full preparation to suppress harmonics with a DC
REACTOR
• An exclusive terminal (P1, P(+)) for connecting a DC
REACTOR is equipped as standard. Connect the optional
DC REACTOR (DCR - ) to reduce harmonics on
power supply side.
4. Suppression of inrush current when the power
supply is turned on
• FRENIC5000G11S series inverters have a built-in circuit that
suppresses inrush current that are generated when the
power supply is turned on. No measures have to be taken to
handle inrush current in particular.
5. Keypad panel designed with six foreign lan-
guages as standard
1) Standard products : English, German, French, Spanish,
Italian, and Japanese
2)
Manufactured on request : Chinese, English, and Japanese
E01 X1 terminal
(Function select)
E02
X2 terminal
E03 X3 terminal
E04 X4 terminal
E05 X5 terminal
F42 Torque vector control 1
F09 Torque boost 1
H06 Fan stop operation
É20 Y1 terminal
(Function select)
F14 Restart mode after
momentary power failure
(Mode select)
F26 Motor sound
(Carrier freq.)
E24 Y5A,Y5C terminal
function
(Relay output)
F41 Torque limiter 1
(Braking)
C01 to C03 Jump frequency 1 to 3
C04 (Hysteresis)
Function
Name Factory setting Recommended setting value Remarks
code
0:
Multistep freq. select (1 to 4 bits) [SS1]
1:
Multistep freq. select (1 to 4 bits) [SS2]
2:
Multistep freq. select (1 to 4 bits) [SS4]
3:
Multistep freq. select (1 to 4 bits) [SS8]
4:
ACC/DEC time selection (1 to 4 bits) [RT1]
0: Inactive
0.0: Automatic torque boost
0: Inactive
0: Inverter running
1: Inactive
2: 2kHz
15:
Auxiliary terminal for 52-1 [AX]
999: No limit
0: No jump frequency
3: 3Hz
0:
Multistep freq. select (1 to 4 bits) [SS1]
1:
Multistep freq. select (1 to 4 bits) [SS2]
2:
Multistep freq. select (1 to 4 bits) [SS4]
17: UP command [UP]
18: DOWN command [DOWN]
1: Active
0.0: Automatic torque boost
1: Active
25: Fan operation signal
3: Active
(Continuous operation; heavy inertia
load, or general load)
15: 15kHz
10: 10kHz
0: Inverter running (RUN)
0: Automatic deceleration control
0 to 120Hz
0 to 30Hz
Setting is also available with E06
to E09.
Used to control the inverter panel
cooling fans for inverters of 40HP
or larger. Also available with
Functions E21 to E23 (Y2 to Y4
terminal functions).
Set H13 to H16 also, if necessary.
For 75HP or smaller inverter.
For 100HP or larger inverter.
Relay output (Y5A, Y5C). On
when inverter output is present.
(Set if necessary.)
Setting recommended when
braking resistor is not used.
Set the value in accordance with
the equipment to be combined.
Chapter6-9(P18˜19).p65
07.8.9, 12:51 Page 19
Adobe PageMaker 6.5J/PPC