Foma M702iG, Manual

Page: 414 / 433

20
e
Click [ キャンセル (Cancel)] on the
Connection screen
The Hyper Terminal entry screen opens.
f
Enter the APN in the following format
y
Press
[Entry Format]
AT+CGDCONT=<cid>,"<PDP type>","<APN>"
<cid>: Enter the registration number (cid) of the
access point (APN). Cid1 is registered
"mopera.ne.jp" and cid3 is registered
"mopera.net" already, when you set cid, 2 or a
number between 4 and 10.
<PDP type>: Enter the PDP type of the APN in
PPP or IP.
<APN>: Enter the access point (APN).
[OK] appears after the access point is set up.
• Enter ATE1 if the entered characters are not
displayed.
■
To reset the APN settings of the specified
cid
Enter AT+CGDCONT=<cid>.
■ To view the registered APN
Enter AT+CGDCONT? .
g
Click "
ファイル
(File)"
y
"
ハイパーターミ
ナルの終了
(Exit Hyper Terminal)"
h
Click [ はい (Yes)] on the conformation to
disconnect screen
y
Click [ いいえ (No)]
on the confirmation to save screen
Hyper Terminal exits and the APN settings
complete.
• APN information is saved on the FOMA handset. If
you connect a different FOMA handset, save the
APN information again.
• If you want to use the APN information saved on the
PC, register the same APN to the same cid on the
FOMA handset.
Setting Display/Hide Caller ID
You can set to display or hide Caller ID for
packet communication using the *DGPIR AT
command.
• To set up 64K data communication connection, this
setting is not required.
a
Perform Step 1 to 5 in "Setting APN"
Hyper Terminal launches and the entry screen
opens.
b
Set whether to display or hide Caller ID
using the following format
y
Press
[Entry Format]
AT*DGPIR=<n>
<n> : Set to 1 to hide Caller ID ("184" is added
when dialing).
Set to 2 to display Caller ID ("186" is added
when dialing).
[OK] appears after Caller ID notification is set.
• To use "mopera U" or "mopera", set to 2 (display
Caller ID).
• Enter ATE1 if the entered characters are not
displayed.
• You can also enter the leading "184" or "186" to the
phone number of an APN for a dial-up connection to
display or hide the Caller ID.
→ P20, P22
If you set Caller ID notification using the *DGPIR
command and the dial-up connection setting, the
dial-up connection setting takes precedence.
For example, even if you set <n> of the *DGPIR
command to 2, entering the leading "184" (hide) to
the APN number in the dial-up network hides the
Caller ID.
• When using overseas, set AT*DGPIR=0 (Default).
Calls will be made according to the registered APN.
Configuring Dial-up Network Settings
Set up the dial-up network on the PC. This
section describes the steps to connect to
"mopera U" that has been set to <cid>=3 in the
USB connection as an example.
• For setting up connections to other than "mopoera U"
or "mopera", contact your ISP.
For Windows XP
a
Click " スタート (Start)"
y
" すべてのプロ
グラム (All Programs)"
y
" アクセサリ
(Accessories)"
y
" 通信
(Communication)"
y
" 新しい接続ウィ
ザード (New Connection Wizard)"
Continued on the next page