Farm King Model 1050 Operator And Parts Manual Download Page 34

Page: 34 / 174

Assembly - 10" Backsaver Auger

Figure 23

Locate the connecting link (Item 1) and link base pin

(Item 2)

[Figure 23]

Link Base Pin Sizes

1” x 20” - Model 1050
1” x 22” - Model 1060
1-1/4” x 26” - Model 1070

Cotter Pin Sizes

3/16” x 1-1/2” - Model 1050 & 1060
1/4” x 2” - Model 1070

Figure 24

Place the connecting link (Item 1) between the LH &

RH lower lift arm mounting holes (Item 2)

[Figure 24]

Figure 25

Install the connecting link base pin (Item 1) through

the LH & RH lower lift arm(s) and connecting link.

Install one 1-1/4” x 10 ga. narrow rim washer (Item 2)

onto the connecting link base pin. Install one cotter

pin (Item 3)

[Figure 25]

through the connecting link

base pin.

Figure 26

Locate the pivot yoke weldment (Item 1) and yoke pin

(Item 2)

[Figure 26]

Yoke Pin Sizes

1” x 16-1/8” - Model 1050
1” x 17-7/8” - Model 1060
1-1/4” x 22-1/8” - Model 1070

Cotter Pin Sizes

3/16” x 1-1/2” - Model 1050 & 1060
1/4” x 2” - Model 1070

B-0614

B-0617

B-0618

B-0615

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands