manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 59

57

Assembly - 10" Backsaver Auger

 

Figure 103

Install the cable clamp (Item 1) 

[Figure 103]

 using the

two bolts provided with winch. Leave bolts loose. 

Route the cable over the top of the hand winch drum.

Install the cable (Item 2) from the inside of the drum

through one of the dimpled holes (Item 3) 

[Figure 103]

in the outer plate.

Loop the cable around the drum bearing. Feed the

cable between the loop and outer plate, then through

the cable clamp.

Leave approximately 1” of cable extending past the

clamp. Tighten and torque the clamp bolts to

approximately 2 ft.-lb. (3 N•m).

Turn handle to wrap cable around drum.

Hopper Safety Hook Installation

Figure 104

Install the quick link (Item 1) through the eye of the

hook (Item 2) 

[Figure 104]

. Install the quick link onto

the safety chain at the desired location. Tighten the

quick link nut to securely fasten the quick link and

hook to the safety chain.

NOTE: The quick link and hook may need to be

adjusted higher on the safety chain to make

sure the hopper is approximately 16” above the

ground for transport.

Do not remove the drum to install the cable.

B-0582

2

1

3

B-0748

2

1

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands