manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 56

54

Assembly - 10" Backsaver Auger

Figure 92

Align the hinged intake auger cover (Item 1) with the

four mounting holes in the hopper. Install four 5/16” x

1” bolts (Item 2) 

[Figure 92]

 and 5/16” lock washers

through the hinged intake auger cover and into the

hopper. Tighten bolts.

Safety Chain Installation

Figure 93

Install the safety chain loop (Item 1) into the opening

on the bottom side of the hitch, install one 3/4” x 2-1/

2” bolt (Item 2) 

[Figure 93]

 through the hitch and

safety chain loop. Install one 3/4” lock nut and tighten

to secure the safety chain to the hitch.

Hydraulic Hose Holder Installation

Figure 94

Install the hydraulic hose holder (Item 1) 

[Figure 94]

onto the mounting bracket located on the top of the

gearbox (above the hitch).

Install one 3/8” flat washer onto one 3/8” x 1-1/4”

bolt (Item 2) 

[Figure 94]

, install the bolt down through

the storage bracket and mounting bracket. Install one

3/8” lock nut on the bolt and tighten to secure the

hydraulic hose holder to the gearbox.

Figure 95

Remove bolt (Item 1) and lock nut. Move the hitch

(Item 2) forward and align the back hole (Item 3)

[Figure 95]

 of the hitch with the hitch mount. Re-

install and tighten the bolt and lock nut.

B-0734

1

2

B-0746

1

2

B-0722

1

2

B-0721

1

3

2

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands