manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 166

164

Specifications - 10" Backsaver Auger

HYDRAULIC CONNECTION SPECIFICATIONS
O-Ring Fitting (Straight Thread)

Lubricate the O-ring before installing the fitting.

Loosen the jam nut and install the fitting. Tighten the

jam nut until the washer is tight against the surface.

O-ring Face Seal Connection
Figure 159

When the fitting is tightened, you can feel when the

fitting is tight to eliminate leakage caused by under or

over torqued fittings. Use petroleum jelly to hold the

O-ring in position until the fittings are assembled.

Flare Fitting
Figure 160

Tighten until the nut makes contact with the seat. Use

the chart 

[Figure 160]

 to find the correct tightness

needed.

NOTE: If the fitting leaks, disconnect and inspect the

seat area for damage.

Port Seal (O-ring Boss) Fitting

Figure 161

NOTE: Port seal and nut, washer and O-ring (O-ring

Boss) fittings use the same tightening torque

valve chart.

If a torque wrench cannot be used, use the following

method.
Tighten the nut until it just makes metal to metal

contact, you can feel the resistance.
Tighten the nut with a wrench no more than one hex

flat maximum.
Do not over tighten the port seal fitting.

NOTE: If a torque wrench cannot be used, use the hex

flat tightening method as an approximate

guideline.

NOTE: Port seal fittings are not recommended in all

applications. Use O-ring boss fittings in these

applications.

Tubelines And Hoses

Replace any tubelines that are bent or flattened. They

will restrict flow, which will slow hydraulic action and

cause heat.
Replace hoses which show signs of wear, damage or

weather cracked rubber.
Always use two wrenches when loosening and

tightening hose or tubeline fittings.

O-ring Face Seal Tightening Torque

Tubeline O.D.

Thread Size

N•m (ft-lb)

1/4”

9/16” - 18

13 (18)

3/8”

11/16” - 16

22 (30)

1/2”

13/16” - 16

40 (54)

5/8”

1” - 14

60 (81)

3/4”

1-3/16” - 12

84 (114)

7/8”

1-3/16” - 12

98 (133)

1”

1-7/16” - 12

118 (160)

1-1/4”

1-11/16” - 12

154 (209)

1-1/2”

2” - 12

163 (221)

Flare Fitting Tightening Torque

Tubeline O.D.

Thread Size

N•m (ft-lb)

1/4”

7/16” - 20

13 (18)

5/16”

1/2” - 20

17 (23)

3/8”

9/16” - 18

22 (30)

1/2”

3/4” - 16

40 (54)

5/8”

7/8” - 14

60 (81)

3/4”

1-1/16” - 12

84 (114)

7/8”

1-3/16” - 12

98 (133)

1”

1-5/16” - 12

118 (160)

1-1/4”

1-5/8” - 12

154 (209)

1-1/2”

1-7/8” - 12

163 (221)

2”

2-1/2” - 12

252 (342)

Port Seal And O-ring Boss Tightening Torque

Tubeline O.D.

Thread Size

N•m (ft-lb)

1/4”

7/16” - 20

13 (18)

3/8”

9/16” - 18

22 (30)

1/2”

3/4” -1 6

40 (54)

5/8”

7/8” - 14

60 (81)

3/4”

1-1/16” - 12

84 (114)

7/8”

1-3/16” - 12

98 (133)

1”

1-5/16” - 12

118 (160)

1-1/8”

1-7/16” - 12

154 (209)

1-1/4”

1-5/8” - 12

163 (221)

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands