manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 35

33

Assembly - 10" Backsaver Auger

Figure 27

Raise the wide end of the pivot yoke weldment and

align with the mounting brackets on the upper lift arm

[Figure 27]

.

Install the yoke pin (Item 1) through the upper lift arm

and pivot yoke weldment. Install one 1-1/4” x 10 ga.

narrow rim washer onto the yoke pin. Install one

cotter pin (Item 2) 

[Figure 27]

 through the connecting

link swivel pin.

Figure 28

Place the narrow end of the pivot yoke weldment

(Item 1) over the end of the connecting link (Item 2).

Place the rod end (Item 3) 

[Figure 28]

 of the hydraulic

cylinder inside the connecting link.

Figure 29

Locate the connecting link swivel pin (Item 1) 

[Figure

29]

.

Connecting Link Swivel Pin Sizes

1” x 5-1/2” - Model 1050 & 1060
1-1/4” x 5-1/2” - Model 1070

Cotter Pin Sizes

3/16” x 1-1/2” - Model 1050 & 1060
1/4” x 2” - Model 1070

Install the connecting link swivel pin (Item 1) through

the pivot yoke weldment, connecting link and

hydraulic cylinder. Install one 1-1/4” x 10 ga. narrow

rim washer (Item 2) onto the connecting link swivel

pin. Install one cotter pin (Item 3) 

[Figure 29]

 through

the connecting link swivel pin.

B-0622

1

2

B-0620

1

3

2

B-0621

1

3

2

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands