Farm King Model 1050 Operator And Parts Manual Download Page 43

Page: 43 / 174

Assembly - 10" Backsaver Auger

Figure 55

Install chain guard (Item 1)

[Figure 55]

Figure 56

Raise the bottom tube section and remove the support

(Item 1)

[Figure 56]

. Lower the tube assembly to the

ground.

Remove strap.

Figure 57

With the tube assembly complete, tighten the castle

nut (Item 1)

[Figure 57]

just enough to install the

cotter pin (Should feel a little tension on the flighting).

NOTE: Bag of hardware for the tube supplies an extra

cotter pin to replace the one removed by the

castle nut when the tube assembly started.

Check for cotter pin hole in the shaft. Tighten or back

the castle nut off (applying some tension on the

flighting) until the closest cotter pin hole(s) is

exposed.
Install the cotter pin (Item 2)

[Figure 57]

Figure 58

Install the dust cap (Item 1)

[Figure 58]

Add 10 pumps of grease to top bearing (Item 2)

[Figure 58]

B-0631A

B-0677

B-0633

B-0661

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands