Farm King Model 1050 Operator And Parts Manual Download Page 33

Page: 33 / 174

Assembly - 10" Backsaver Auger

Figure 20

Align and lower the upper lift arm (Item 1) down over

the LH & RH lower lift arm mounting brackets (Item 2)

[Figure 20]

Figure 21

Align the mounting holes of the upper lift arm with

mountings hole in the LH & RH lower lift arm

mounting brackets

[Figure 21]

Lift Arm Clevis Pin Sizes

1” x 2-13/16” - Model 1050 & 1060
1-1/4” x 2-13/16” - Model 1070

Cotter Pin Sizes

3/16” x 1-1/2” - Model 1050 & 1060
1/4” x 2” - Model 1070

Install one lift arm clevis pin (Item 1) from the outside,

through the upper lift arm(s) and lower lift arm(s).

Install one 1-1/4” x 10 ga. narrow rim washer (Item 2)

onto the two lift arm clevis pins. Install one cotter pin

(Item 3)

[Figure 21]

through the two lift arm clevis

pins.

Lower the upper lift arm onto the cradle.

Remove strap.

NOTE: It is recommended to leave the plastic on the

hydraulic cylinders during assembly. This will

help to prevent damage to the paint and

minimize touch-up painting.

Figure 22

Place the base end of the hydraulic cylinder between

the upper lift arm mounting brackets

[Figure 22]

Top Cylinder Pin Sizes

1” x 6-1/2” - Model 1050
1” x 6-7/8” - Model 1060
1-1/4” x 7-3/4” - Model 1070

Cotter Pin Sizes

3/16” x 1-1/2” - Model 1050 & 1060
1/4” x 2” - Model 1070

Install the top cylinder pin (Item 1) through the upper

lift arm and hydraulic cylinder. Install one 1-1/4” x 10

ga. narrow rim washer (Item 2) onto the cylinder pin.

Install one cotter pin (Item 3)

[Figure 22]

through the

cylinder pin.

B-0604

B-0605

Installing the hydraulic cylinder will require two

people. One person to hold the hydraulic cylinder in

position and the second person to install the cylinder

pin.

B-0616

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands