manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 29

27

Assembly - 10" Backsaver Auger

Figure 6

Align the left undercarriage arm (Item 1) with the tab

(Item 2) 

[Figure 6]

 on the axle.

Install two 3/8” x 4-1/2” bolts (Item 3) 

[Figure 6]

 and

3/8” lock nuts. Do not tighten bolts and nuts at this

time.
Align and install the right undercarriage arm (opposite

side of axle).

Figure 7

Install a strap (Item 1) around the center of the axle

(Item 2) 

[Figure 7]

.

Connect the strap to an approved lifting device.
Raise the axle high enough to install tires.

Figure 8

Install the tire with the valve stem facing out (both

sides). Install the five wheel nuts (both sides) 

[Figure

8]

.

Tighten wheel nuts in a criss-cross pattern 

[Figure 8]

.

Tighten wheel nuts to 80 - 100 lb. / ft. (108 - 135

N•m) of torque.

Lower the axle and tires to the ground. Remove the

strap and lifting device.

Check tire pressure.

NOTE: Recommended tire pressure is 35 PSI 241 kpa)

maximum.

B-0587

1

2

3

B-0589

1

2

B-0590

2

5

3

4

1

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands