manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 30

28

Assembly - 10" Backsaver Auger

Figure 9

Align the undercarriage tie plate (Item 1) 

[Figure 9]

with the mounting plates on the LH & RH

undercarriage arms.

Install four 3/8” flat washers onto four 3/8” x 1-1/4”

bolts (Item 2) 

[Figure 9]

. Install the bolts, then install

3/8” lock nuts on each bolt. Do not tighten at this

time.

Figure 10

Locate the LH (Item 1) & RH (Item 2) 

[Figure 10]

undercarriage arches.

NOTE: The undercarriage arches are stamped (Item 3)

[Figure 10] with an L & R for identification.

Figure 11

Align the LH undercarriage arch (Item 1) 

[Figure 11]

,

on the outside of the mounts on the undercarriage arm

and axle. 
Install one 5/8” flat washer on two 5/8” x 1-3/4”

bolts (Item 2) 

[Figure 11]

. Install the two bolts with

flat washers from the outside (through the

undercarriage arch first). Install a 5/8” flat washer and

lock nut onto each bolt. Do not tighten at this time.
Align and install the RH undercarriage arch.

Figure 12

Locate and install one undercarriage arch brace (Item

1) 

[Figure 12]

 onto the undercarriage arm and LH

undercarriage arch.
Install one 5/8” flat washer on two 5/8” x 1-3/4”

bolts (Item 2) 

[Figure 12]

. Install the bottom bolt with

flat washer from the outside (through the

undercarriage arch brace first). Install the top bolt with

flat washer from the top (through the undercarriage

arch brace first). Install a 5/8” flat washer and 5/8”

lock nut onto each bolt. Do not tighten at this time.
Install the second undercarriage arch brace (LH side).

B-0592

1

2

2

B-0593

2

1

3

B-0596

1

2

2

B-0597

1

2

2

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands