manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 58

56

Assembly - 10" Backsaver Auger

bracket. Install one 7/16” flat washer and 3/8” lock

nut on the three bolts. Tighten bolts and nuts.

Figure 100

Align the handle (Item 1) 

[Figure 100]

 with the input

shaft.

Install the nut (Item 2) 

[Figure 100]

. Tighten the nut

against the handle and torque to 22 - 25 ft.-lb. (30 -

34 N•m).

Figure 101

Locate the winch cable. Install the open end of the

cable (Item 1) 

[Figure 101]

 over the pulley on the top

of the lift boom. 

Figure 102

Feed the open end of the cable (Item 1) 

[Figure 102]

through the slot(s) and around the lower pulley on the

bottom of the lift boom.

Route the cable to the hand winch.

B-0719

1

2

•

Do not over torque the nut against the handle.

•

Do not adjust the double lock nuts on the long

end of the input shaft.

B-0741

1

B-0742

1

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands