manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 32

30

Assembly - 10" Backsaver Auger

Figure 16

Align and install the lower lift arm (Item 1) between

the LH & RH lower lift arms using eight 5/8” x 1-3/4”

bolts (Item 2) 

[Figure 16]

 and eight 5/8” lock nuts. Do

not tighten at this time.

Figure 17

Align and install the lower lift arm (Item 1) between

the LH & RH lower lift arms using eight 5/8” x 1-3/4”

bolts (Item 2) 

[Figure 17]

 and eight 5/8” lock nuts. Do

not tighten at this time.

Figure 18

Install the lift cross member (Item 1) between the LH

& RH lower lift arms, using two 3/8” x 4” bolts (Item

2) 

[Figure 18]

.

Figure 19

Install the lift cross member (Item 1) between the LH

& RH lower lift arms, using six 1/2” x 1-1/2” bolts

(Item 2) 

[Figure 19]

 and six 1/2” lock nuts.

Install a strap around the upper lift arm.
Connect the strap to an approved lifting device.
Raise and move the upper lift arm over the LH & RH

lower lift arms.

NOTE: The following images may not show your exact

lift cross member as it appears but the

procedure is correct.

B-0602

1

2

2

EARLIER MODELS

B-0606A

1

2

2

LATER MODELS

B-0603

1

EARLIER MODELS

2

B-0768

1

2

LATER MODELS

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands