Farm King Model 1050 Operator And Parts Manual Download Page 50

Page: 50 / 174

Assembly - 10" Backsaver Auger

Figure 74

Install a strap (Item 1) around the yoke pin. Attach the

strap to an approved lifting device.
Swing the lift arm cradle (Item 2)

[Figure 74]

to the

side to allow the lift assembly to be raised above the

lift arm cradle. Re-install the lift arm cradle.

Figure 75

Lower the tube / undercarriage assembly down onto

the cradle (Item 1)

[Figure 75]

. Center the tube /

undercarriage assembly on the cradle.
Tighten all remaining undercarriage bolts.
Lower tube assembly onto the undercarriage and

remove the strap from tube assembly.

Grease all zerks on undercarriage. (See

“LUBRICATION” on page 89.)

Installing The Intake Auger

NOTE: The following images may not show your exact

intake auger as it appears but the procedure is

correct.

Figure 76

Install the u-joint (Item 1) onto the shaft (Item 2)

[Figure 76]

of the upper gearbox (intake elbow).

Apply Locktite® to the set screw (Item 3)

[Figure 76]

install and tighten the set screw.

B-0668

B-0671

Check over undercarriage, verify all bolts are tight, all

zerks are greased and cotter pins bent over.

B-0701

Position the u-joint center (Item 4) [Figure 76] at the

same height as the pivot mounting holes.

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands