Farm King Model 1050 Operator And Parts Manual Download Page 98

Page: 98 / 174

Maintenance - 10" Backsaver Auger

SAFETY SIGN (DECAL) INSTALLATION

Procedure

•

Remove all portions of the damaged safety sign

(decal).

•

Thoroughly clean the area with glass cleaner.

Removing all adhesive residue.

•

Allow the area to dry completely before installing

the new safety sign (decal).

•

Position the safety sign (decal) in the correct

location. Remove a small portion of the backing

paper on the safety sign (decal).

•

Press on the safety sign (decal) where the backing

paper has been removed.

•

Slowly remove the remaining backing paper,

pressing on the safety sign (decal) as the backing

paper is removed.

•

Using the backing paper, pressing firmly, move the

backing paper over the entire safety sign (decal)

area.

NOTE: Small air pockets can be pierced with a pin and

smoothed out using the piece of the backing

paper.

When replacing safety signs (decals), the

temperature must be above 10° C (50° F).

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands