manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual, Page: 40 / 174

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 40

38

Assembly - 10" Backsaver Auger

Figure 43

Install a chain (Item 1) 

[Figure 43]

 onto the input box.

Connect the chain to an approved lifting device.
Raise and move the input box in front of the bottom

tube section.
Remove chain guard (Item 2) 

[Figure 43]

.

Figure 44

Align and guide the input box onto the flighting of the

bottom tube section 

[Figure 44]

.

Figure 45

NOTE: When installing the input box onto the

flighting, guide the splined shaft through the

opening on the opposite end of the input box.

Guide the input box onto the flighting of the bottom

tube section until the two mounting flanges make

contact 

[Figure 45]

.

Align the holes of the two mounting flanges. Install

the six 1/2” x 1-1/4” bolts (Item 1) 

[Figure 45]

through the bottom tube section flange and into

threaded holes of the input box. Tighten the bolts.

Figure 46

Install one bearing flange (Item 1) 

[Figure 46]

 over the

drive stub shaft.

Install the 1-3/8” bearing (Item 2) 

[Figure 46]

 onto the

drive stub shaft.

B-0631

1

2

B-0634

B-0636

1

B-0637

1

2

Summary of Contents for Model 1050















































































































































































Reviews:

No comments