manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 47

45

Assembly - 10" Backsaver Auger

Figure 66

Align the discharge spout (Item 1) with the mounting

brackets (Item 2) 

[Figure 66]

 on both sides of the top

tube section.

Install the four 3/8” x 2” (full thread) bolts (Item 3)

[Figure 66]

 and 3/8” lock nuts. Tighten bolts and lock

nuts evenly until the discharge spout contacts the top

tube section.

Lower the tube assembly to the ground.

Installing Tube On Undercarriage

Install the tube on the undercarriage on a flat level

surface.

B-0662

1

2

3

Check over all tube and bridging hardware to make

sure all hardware Is tight before Installing tube

assembly onto the undercarriage.

•

DO NOT permit bystanders to be in the work area

when unloading and assembling the auger

components.

•

DO NOT work under suspended parts.

•

Keep away from moving parts.

•

Always use lifting devices / vehicles, chains or

straps of adequate size and strength when

unloading and assembling the auger components.

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when

assembling the equipment.

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands