Farm King Model 1050 Operator And Parts Manual Download Page 91

Page: 91 / 174

Maintenance - 10" Backsaver Auger

LUBRICATION

Recommendations

Always use a good quality multi-purpose / lithium base

grease when lubricating the equipment.

•

Always use a hand-held grease gun.

•

Clean fitting before greasing, to avoid injecting dirt

and grit.

•

Replace and repair broken fittings immediately.

•

If fittings will not take grease, remove and clean

thoroughly. Replace fitting if necessary.

Locations

Lubricate the following grease locations EVERY 8

HOURS:

Figure 144

Apply two pumps of grease to the lift arm pivot (Item

[Figure 144]

Do not over-grease bearings. Greasing too often can

damage seals and lead to premature bearing failure.

Fluid such as engine oil, hydraulic fluid, coolants,

grease, etc. must be disposed of in an

environmentally safe manner. Some regulations

require that certain spills and leaks on the ground

must be cleaned in a specific manner. See local, state

and federal regulations for the correct disposal.

B-0665

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands