manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 49

47

Assembly - 10" Backsaver Auger

Figure 71

Remove the 1/2” x 1-1/4” bolt (Item 1) 

[Figure 71]

, 1/

2” lock nut and 1/2” flat washer from the lift arm

cradle.

NOTE: Loosening the lift arm cradle will allow the RH

& LH undercarriage arms to be moved during

installation to the tube assembly.

Figure 72

Fully install the RH & LH undercarriage arms (Item 1)

[Figure 72]

 onto the mounts of the bottom tube

section.

Align the undercarriage tie plate and install the two 3/

8” x 1-1/4” bolts (Item 1) 

[Figure 70]

, 3/8” lock nut

and 3/8” flat washers. Do not tighten bolts and lock

nuts at this time.

Figure 73

Raise the upper lift arm (Item 1), align upper lift arm

with the main bridging yoke (Item 2) 

[Figure 73]

 on

the bottom tube section.

Lift Arm Pivot Pin Sizes

1” x 11-7/8” - Model 1050 & 1060
1-1/4” x 12-1/4” - Model 1070

Cotter Pin Sizes

3/16” x 1-1/2” - Model 1050 & 1060
1/4” x 2” - Model 1070

Install the lift arm pivot pin (Item 3) through the main

bridging yoke and upper lift arm. Install one 1-1/4” x

10 ga. narrow rim washer (Item 4) onto the lift arm

pivot pin, and install one 1/4” x 2” cotter pin (Item 5)

[Figure 73]

 through the lift arm pivot pin.

B-0669

1

B-0664

1

B-0665

1

2

3

4

5

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands